LOCKING LANYARD

  •  The lanyard pin helps elongate the limb when donning.
  •  The pin gives audible confidence of engagement.
  •  The o-ring at the end of the pin creates an airtight socket helping to reduce air noise.

Fabrication with the “5 Degree AK Connector eliminates the need for offset components.

Same simple fabrication as the Deep Air-Lock and Deep Easy-Off Lock pin systems.

CD117L |  Easy-Off Locking Lanyard

Lever Design / Push Button, lanyard lock

CD103L |  Air-Lock Locking Lanyard

Push Button Design, lanyard lock

  •  Easy donning and doffing with lever release
  •  Water-resistant
  •  Airtight “suction” with the safety and security of a pin
  •  Suction allows for less traction on the limb for increased comfort and decreased liner wear
  •  Expulsion valve or suspension sleeve are not needed to maintain suction in most cases
  •  Water-resistant

5 Degree AK Connector, Deep Air-Lock and Deep Easy-Off Lock are sold separately.

CD118P |  Locking Lanyard Pin

Airtight, water-resistant, lanyard lock

 

  • The lanyard pin helps elongate the limb when donning.
  • The pin gives audible confidence of engagement.
  • The o-ring at the end of the pin creates an
  • airtight socket helping to reduce air noise.

 

Same simple fabrication as the Deep Air-Lock

and Deep Easy-Off Lock pin systems.

It is recommended to use the Deep Air-Lock or Deep Easy-Off Lock with the Locking Lanyard Pin.

 

CD118P Locking Lanyard Pin Instructions pdf

Coyote Design CD103AF Alignable Connector Coyote Design CD111AF One Shot Connector

CD103AF

Alignable Connector

Offset up to 0.6"

 

CD103P8

Extra 8-click Pin

1.3" long includes spacers

 

CD103P11

Extra 11-click Pin

1.65" long includes spacers

 

CD103WH

Lock wrench

Makes maintenance easy

 

CD111

One-Shot Connector

Offset up to 0.6"

 

CD103SDI

Single Direction Insert

Offset up to 0.33"

 

CD103MDI

Multi-Direction Insert

Offset up to 0.33"

 

Coyote Design CD103WH Lock Wrench used with Air-Lock

CD103ELD

Exo Lamination Plug

Used when fabricating the Air-Lock in Exo sockets.

Coyote Design CD103ELD Exo Lamination Plug used with Air-Lock

CD103P8H Brass Pin

Extra 8-click Pin

1.3" long includes spacers

 

CD103P11H Brass Pin

Extra 11-click Pin

1.65" long includes spacers

 

CD103P8S Solid Plastic Pin

This pin is for low activity only (K2)

Extra 8-click Pin

1.3" long includes spacers

 

CD1118P Locking Lanyard Pin

11-click Pin with Lanyard and O-ring

1.65" long includes spacers

CD118PD Lanyard Pin Disk

Disk for attaching lanyard to socket

Sold Separately

CD103GP Guide Pin

Guide Pin - helpful in drilling out bottom of Air-Lock or Easy-Off Lock.

The CD103RBC Release Botton Cover

Added to end of release button to make it easier for patients to release the lock. Ideal for geriatric patients or others with lower dexterity or limited hand strength.

CD115CF5 | 5 Degree AK Connector

Capable of up to 1.5” of Offset with 5 degrees of flexion angle. The 5 Degree AK Connector is used primarily with the Coyote Design Lanyard Lock CD118 but can be used with Coyote Design pin systems or other locks in combination with the Integrator. Can be glued to the lock in any offset position for fabrication into the socket. Eliminates the need for offset components. For lamination or thermoforming. 265 lb. weight limit.

ADDITIONS

Coyote Design CD103SDI Single Direction Connector
Coyote Design CD103P8 Pin. Used with Air-Lock and Easy Off Lock
Coyote Design CD103P11 Pin. Used with Air-Lock and Easy Off Lock

Fabrication for Locking Lanyard Pin and 5 Degree Connector.

Thorough video of entire Air-Lock fabrication process.

Single Lamination and Offset Fabrication

The fabrication procedure for the Air-Lock and Easy-Off Lock

is a time and money saver. The Alignable Connector is

attached to the lock in the desired location for prosthetic

alignment, allowing the lock to remain in ideal lock alignment

for easy engagement. A single lamination is done that

incorporates the lock and the connector into the socket. The

offset capability saves money by eliminating need for offset

components, and saves time with a single lamination and

easy component setup.

 

Billing Information

Coyote Design® believes that “suction” in a prosthetic refers to negative pressure created inside the socket, rather than componentry such as an expulsion valve or sleeve. Because we think of suction as a function, we believe it should be permitted to bill L5671 in conjunction with the L5647 or L5652 in cases when it is medically necessary. As with other situations where multiple suspension methods are used and billed we feel the combination of a lock and suction helps to increase safety for the patient.

 

For more information on billing the Air-Lock and on our socket pressure study between airtight and tradition pins contact Coyote Design.

For United States product sales please contact one of these distributors.

For international product sales please contact one of these distributors.

United Kingdom

Spain & Portugal

Netherlands

France

Australia & New Zealand

Canada

 

Kanae

Orthopedic Services

Japan

Germany

Norway

INTERNATIONAL

for all countries not listed