Casting Handle
We struggled with definition of the distal end of the liner , the fit between the lock and liner, and the lock location during casting. To speed up the casting process, and to help ensure proper lock alignment we use the casting handle. The lock anchors are placed into the handle prior to filling the cast, and this speeds up fabrication and eliminates the risk of the lock being fabricated in the wrong location.
CD316—Casting Handle and Pin for Suction Lock , EOVC, and Lanyard Locks
CD316A—Casting Handle and pin for Air-Lock
CD316SA—Casting Handle and Pin for Small Air-Lock
Silicone Molded Distal Cushions
We have found that the shape of most larger diameter locks do not fit with the distal ends of liners as well as they should . To create an intimate fit between lock and liner we created silicone cushions with multiple sizes and shapes. These also help ensure that the pin is seating completely with ZERO play, and offer extra cushion on the distal end. A cushion is glued to the end of the liner using a sili- cone adhesive. (silicone adhesive not included) Silicone Distal Cushions are not recommended for use with the Air-Lock and Small Air-Lock. Call coyote for more information on adhesive options.
CD112-Set of four Silicone Distal Cushions
CD112SS—Small Silicone Style Molded Distal Cushion
CD112MS—Medium Silicone Style Molded Distal Cushion
CD112LS—Large Silicone Style Molded Distal Cushion
CD112MG—Medium Gel Style Molded Distal Cushion
Memory Foam Distal Cushions Instead of different shapes to create an intimate fit, you can use the memory foam version to fill the gap between the liner and the lock. These cushions help ensure proper seating, and keeps the lock from being in between clicks. A cush- ion is glued to the end of the liner using a unique adhesive, some liners need to be rough on the distal end for adhesive. If using Air-lock, a distal cushion is rarely needed, but when needed, the memory foam cushions are the best choice.
CD112MF—Memory Foam Distal Cushion with adhesive (pack of 3) adhesive is included
Casting Bungee
Adjustable length allows you to keep casting stockinette pulled taut during the casting process on virtually any patient. Use during casting for wrinkle free casts.
CD306—Adjustable Casting Bungee
Casting and Fab Dots 
Easily mark problem areas during the casting process using these adhesive foam dots. In place of pen or pencil marks these dots are placed on the liner over the top of problem areas, or areas in need of extra relief. The adhesive back will keep them in place during casting. Once the cast is filled, the 1/8″ thick dots are clearly visible on the mold. These are also used in our lock fabrication.
CD103LFC—Large dots with a .87 Diameter come in packs of 50
CD103SFC—Small dots with a .38 Diameter come in packs of 200
Casting Bag The casting bag, as seen in the RCR workshop . These bags allow for the high tension wrap that is used in the RCR Socket, and makes removal easy.
CD308—Pack of 100
Fiberglass Casting Tape Fiberglass Casting Tape allows for the high tension wrap casting that is used in the RCR Socket. This is NOT conform- able fiberglass. Sold in 2″, 3″ 4″, and 5″. Sold only by the case Direct Sales Only.
CD312C—case of 2″ fiberglass (100 rolls)
CD313C—case of 3″ fiberglass (100 rolls)
CD314C—case of 4″ fiberglass (100 rolls)
CD315C—case of 5″ fiberglass (100 rolls)
Volume Management Pads Some areas of a limb can tolerate more pressure or tighter suspension than others. Rather than global reductions, make volume adjustments to your sockets right where you want them with our six different socket pads. Sold precut in a complete set at full thickness (3/16″) for limitless customization. Surface of pads helps increase suspension in the socket without interfering with donning and doffing.
CD307—set of 2 each of 6 styles
Pylon Spacers These plastic spacers that are inserted into the tube clamp adaptor make small height adjustments easy and fast.CD302—set of two each of the 1/4″ and 1/8″ spacers